Understanding Plumbing Basics When Installing a Bathtub
Understanding Plumbing Basics When Installing a Bathtub
Blog Article
The article author is making several great points on Installing A Bathtub as a whole in this content below.
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old bath tub with a brand-new one is additionally a moderately difficult task. If the old bathtub is conveniently available, the task can move immediately; if you have to open up a wall to eliminate the old bathtub and also place the new bathtub, the task is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as embeded in the new one. Ensure you have certified yourself for the work and are comfortable trying it. Instead of hiring a service provider to take control of a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you may require a specialist plumber to make tube connections.
This write-up will aid you mount a brand-new bathtub in your washroom if you have already bought a new bathtub and also do not require to change the setup of your previous supply of water pipelines.
Your tools as well as material list need to make up the following:
Planning for the Installation
First of all, the sustaining frame provided with the bathroom ought to be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to stop strain on the tub.
Fit the versatile tap ports to the bottom of the two faucets making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you utilize all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should now prepare to be suited its last setting.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you need to do is separate the water supply. After doing so, activate the taps to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be rather problematic because of the restricted access that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will originate from the pipelines. As soon as the supply pipes have been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any old securing compound.
Before carrying on to fit the new faucets, contrast the pipe links on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Utilizing both wood boards under its feet, put the bathtub in the required position. The wood boards are practical in uniformly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by examining the level and also changing the feet on the bathtub up until the spirit level reads degree.
To mount taps, fit the bottom of the furthest adaptable tap adapter to the ideal supply pipe by making a compression join; after that do the same for the various other faucet.
Turn on the water system and also check all joints as well as new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and likewise examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, take care of the bathroom paneling as defined in the producer's user's manual. Tiling as well as securing around the bath tub must wait up until the tub has been made use of a minimum of when as this will certainly resolve it into its final setting.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin making sure that the washing machines are in place between the faucet and also the sink. Safeguard the faucet in place with the maker given backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical tap adapters. The previous type should be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to fracture a stiff seal, triggering the water to penetrate the wall surface between the bath and the tiling, resulting in difficulties with moisture and also possible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components as well as fittings. They are offered in tubes and cartridges, as well as can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Remember to always fill the bath tub with water prior to securing, to enable the activity experienced when the tub is in use. The sealer can split fairly early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly available on the market. It is advisable to fit the ceramic tiles using waterproof or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent person who reads about How to Install a Bathtub, I thought sharing that piece was a good idea. Sharing is good. Helping others is fun. Thanks for your time. Don't hesitate to stop by our website back soon.
Plumbing woes? Connect. Report this page